Primrose Corner

I hate starting with an apology but the photo’s seem a little dark (It’s the torrential rain, you know.) even with all my manipultions in Lightroom. (I don’t know much beyond the very basics I’m afraid.) Anyway, on this dark and dreary day, here is a simple tote bag made fron Amy Butler’s home decor weight, Nigella fabric and a plain (I think you’re supposed to call them solids.) black fabric with a subtle basketweave pattern.

Vital statistics

It’s 12 inches wide, 1 1/2 inches wide, 14 inches tall and a 28 inch fabric handle.

It has a fabric handle (28 inches finished length), Nigella fabric on one side and the plain fabric on the other. It’s stitched along it’s length four times for added strength. It’s also interlined with a medium weight interlining which was a little bit of overkill given the heavier weight of the nigella fabric. I think I’d use a lighter interlining next time, if I felt it needed any at all.

The handle is looped through a nickel o-ring and sewn down in rectangle to try and keep everything tidy and nice.

The bag is lined with a solid dark burgundy fabric with a divided slip pocket in the same fabric. The pocket is trimmed with the main Nigella fabric. It has a magnetic snap to add a little security and help keep everything tucked safely inside.

I made and then added some black piping to the top edge of the bag, I’m not sure that I’d do this again because I don’t think it’s adds anything much. Perhaps in a different colour it would have made more of an impact?

I’ve started adding a extra piece of interlining over the back of magnetic snaps I add to my bags. To explain; in a bag like this I add the magnetic snap to the lining. The lining will also have an interlining, so that’s one piece of fabric ( the lining) plus the interlining. Through this I add the magnetic snap, then insert a further square of interlining over the prongs at the back and add the ‘washer’ part of the snap and fold the prongs inwards . (I know a lot of people like to fold the prongs outwards.) Over this, I sew a further square piece of interlining which covers the whole magnetic snap and protects the exterior fabric (the outside of your bag), which I also interline, from any wear and tear caused by the movement of the snap against the bag fabric. It’s a lot more complicted to explain than to do.

Why do I do this? Well…. it’s because I lost a much loved bag to constant use - the magnetic snap constantly pulling and rubbing against the fabric began to wear it away when the rest of the bag was fine. Sad……. so very sad.

Any tips, hints, suggestions for taking photo’s of bags (better than this anyway!) ?

Whilst sorting out clothes that no longer fit, have disintegrated and otherwise just need to go (and make room in bulging cupboards for stuff we do need). I was surprised how much denim there was in the pile. Some were just grown out of, others were barely hanging together, no longer fit even for gardening in. What to do ?

Recycling I thought and then I remembered reading a book called ‘Patchwork Pizzazz’ by Lise Bergene. In it she describes making bags (quilts and cushions) using a ‘frayed edge technique’, which she’d come across on one of her trips. She uses quilt weight cottons as well as denim in her ‘frayed’ projects. I think others may call this approach ’scrappy’. Just think though denim and fraying ……that’s a marriage made in heaven isn’t it?

I can’t argue that this is a totally eco-friendly project unlike Dottycookie who is re-purposing sheets (What happened to the Barbie sheet?) or Linaloo who issued the re-purposing challenge but these little bags are quite good fun to make. There’s a lot of scope for quite varied styles from shabby chic to just plain shabby, as many ‘looks’ as there are for jeans I suppose.

Let me know what you think to the tutorial - I need your feedback. I’d like to get better at it you see.

To create a characterful denim bag

First identify the pair or pairs of jeans that you’re going to butcher cut up. (It’s definitely best to get permission from the jeans’ owner before you cut them up. People can be ‘funny’ about these things and I’d hate to cause any arguments.)
And yes, I know you’re all ‘growed up’ people but think about your precious fingers when chopping up denim. Those seams can be tough - take care!

Another friendly piece of advice is that you should only embark upon this project if you’re psycholoigcally strong enough to cope with all the little thready bits it creates that secretly migrate to the furthest reaches of your house. (Check the calendar - any important visitors about to pop in? No. O.K, maybe you can get on now.)

You will need;

Bag exterior
• 2 pieces of denim fabric 23cm (9 inches) by 30.5cm (12inches) for the front and back
• 2 pieces of denim 5 cm (2 inches) wide and 30.5cm (12 inches) deep for the bag sides
• 1 piece of denim for the bag bottom 5cm (2 inches) wide by 23cm (9 inches).

Lining

• 2 pieces of lining fabric 23 cm (9 inches) by 30.5cm (12 inches) for the front and the back
• 2 pieces of lining fabric for the sides 5cm (2 inches) by 30.5cm (12 inches)
• 1 piece of lining fabric for the bottom 5cm (2 inches) by 23cm (9 inches).

Batting/wadding/fusible fleece

• 2 pieces of Batting/wadding/fusible fleece 23cm (9 inches) by 30.5cm (12 inches) for the front and back
• 2 pieces of Batting/wadding/fusible fleece 5cm (2 inches) by 30.5cm (12 inches) for the sides
• 1 piece of Batting/wadding/fusible fleece 5cm (2 inches) by 23cm (9 inches) for the bottom.

Backing pieces - this is the fabric you want to show through your design (’through the holes’)

• 2 pieces of denim backing fabric 23cm (9 inches) by 30.5cm (12 inches).

Bag handle

To make a bag handle like mine you need;

• 1 piece or pieces of denim sewn together 5cm (2 inches) wide and 89cm (35 inches) long.

(Note:

if you piece/sew denim strips together to make the handle remember to have the seams on the rightside of the fabric facing outwards)

• 1 piece of wadding/batting/fusible fleece 2.5cm (1 inch) wide and 86cm (34 inches) long.
• 1 piece of fabric 5cm (2 inches) wide by 89cm (35 inches) long.

Other (mostly) necessary pieces of equipment

• scissors (for cutting fabric, thread, etc)
• Cutting board
• Rotary cutter (optional)
• Ruler (optional)
• pins
• matching thread
• non-permanent fabric marker
• embroidery threads (optional)
• buttons (optional)
• sewing needle
• sewing machine
• denim sewing machine needle
• tape measure
• A4 piece of paper (optional)

Seam allowance is 1.5 cm (approximately half an inch) throughout.
When selecting the pieces of denim to isolate and cut out try to avoid having any weak/well worn pieces or tough seamed pieces in the stressy areas of your bag. I’m thinking of where the sides get sewn into the bottom piece and where you want to attach the handles. Permanent grass, mud or oil stains may not look too attractive either. So pick and choose and have a little fun. The denim can be pieced together to make bigger pieces, just put any seams on the outside (so we can fray ‘em)

Step 1 Cut out the denim pieces. It’s a good idea to cut out the larger pieces first and then decide where to cut the smaller pieces from. Try cutting off a leg piece then cut up the inside leg seam and open the fabric out. Use your ruler and rotary cutter to cut out your pieces. If this proves difficult because of seams preventing the ruler laying flat and secure don’t risk slipping with your rotary cutter. Use a piece of paper (newspaper - any sort of paper) to mark out a pattern and use that to cut out your bag pieces with. You may wish to incorporate the jeans pockets into your bag. Take a minute to think about the look you’re aiming for and then cut.	You can see where I was ‘playing’ around with a design on the paper. Didn’t use it!
Cut out denim pieces for the handle Cut out as many pieces as will make a handle 5cm (2 inches) by 89 cm (35 inches) long. We’ll sew those together later.	These are the front, back, sides and handles pieces all cut out.
Cut out fabric to go behind the ‘holey’ design. This fabric goes behind the denim. It shows through the ‘holes’ you fray in the denim, supports the denim in those weakened areas and adds a splash of colour in the seams.You can choose to be subtle with co-ordinating blues or garish with hot, exotic reds and oranges. If you’re going to make ‘holes’ on the back and front of the bag then you need a piece to go behind the front and the back only. If you want to add a ‘fray design’ in the bag sides then you will need side pieces too. Use the measurements as for the lining sides. (This will make perfect sense soon. I promise)	My ’support’ pieces for the front and back on my bag. I used this fabric. Link
Cut out lining pieces Cut out all the lining pieces (front, back, sides and bottom) and the fabric backing for the handle. I chose a pretty little polka dot for my lining. Link
Cut out all the fusible fleece/wadding pieces Cut out all the wadding or fusible fleece pieces. I’ve tried both sorts when making these types of bags and both work perfectly well.	What a lot of pieces!
Mark out your design Now that you’ve cut out all your bag pieces it’s time to mark out you design onto the denim. I tried out some different ideas with patches and hearts and all kinds of shapes. I sewed a running stitch using embroidery thread along the seam (my daughters favourite jeans have this design on them) and drew a square and then played about with some arty lines.
I embroidered the lines I’d drawn onto the front and the back and sewed on some little pink buttons to resemble flowers.	Still thinking about patches!
Get happy with the scissors Now that you’ve decided on your design you need to cut into the shapes you’ve marked out. The things you need to think about are; Leave about 1cm seam (approximately 1/2 an inch) allowance inside your drawn shape. It doesn’t need to be perfectly accurate, it isn’t that kind of project. The fraying looks good when it’s a little random. If the shapes you’ve drawn are enclosed shapes like the square inside the square that I’ve drawn, cut out the middle square but I can only snip into the outer square. If I cut out both, the central square will fall out! I will be able to cut the square out later after stitching my design and avoid damaging the backing fabric. If you’ve drawn curvy, wavy lines which stretch fron one side of the denim front/back to the other then skip this section for now because you’ll be able to insert your scissors between your sewing without risking cutting into the backing fabric.	Cutting into the middle square I’ve cut out the middle square but only snipped into the outer square, otherwise the middle piece will fall out. This way I’ll be able to cut it out later.

Construction

This bag is quilted together as one piece. If you wish to install the lining separately then ignore the instructions concerning the lining. Construct your lining in the same way as the bag outer. The reason for constructing it as one piece is so that the colour of the lining shows in the outside facing seams - more of a colour sensation. You are of course free to choose. (I won’t sulk!)

Making the bag exterior front/back panel Make a fabric sandwich by placing the lining piece face down on your work table. Place the fusible fleece/wadding centrally on top with a even space all the way around. (The aim is that the wadding/fusible fleece will not show in the seams - they’ll be enclosed by the stitching.) Place the ‘backing fabric’ right side facing up on top of the wadding/fusible fleece. Then place the denim fabric right side facing up on top of that. Phew! four pieces of stacked fabric. You should now see your backing fabric peeping through your design (at least you will do if your design required you to cut pieces out at this point.)	Fusible fleece centrally placed on the fabric. Looking good.
Sewing your design If you’re using fusible fleece, fuse your pieces together, ensuring that everything is square and even. If you’re using a non-fusible wadding/batting then pin everything squarely together to prevent ’slippage’ whilst you sew your design. Stitch through these four layers, using your sewing machine denim needle. Follow the line of the design you’ve drawn. Complete the sewing for all of your design and for all pieces.
Prepare the bottom piece Place your ‘bottom’ lining piece right side facing down on your work table and place the fusible fleece/batting centrally on the top. Place the ‘bottom’ denim piece right side facing up on top of this. (Another sandwich.) Fuse together if appropriate, otherwise you may wish to  pin these layers together whilst you fix the bottom to the front and back pieces. Alternatively you could sew down the middle of the wadding to hold it in place.(If you’re using a matching thread this will probably be almost invisible.)	Fusible fleece placed centrally on the bottom piece. I pinned down the middle.
Attach the bottom piece Place one of the exterior (front or back) bag pieces right side down on your work table. Place the denim bottom piece, right side facing up against the bottom edge of the exterior bag piece. The linings should be facing one another. Pin the bottom piece to one exterior piece. Leave a 1.5cm open (unstitched) at the beginning and at the end of the seam to allow for sewing in the side pieces. Sew together using a 1.5cm (half an inch) seam allowance. Remember that the seams need to be facing outwards. Fix the other side of the ‘bottom’ piece to the bottom edge of the other exterior bag piece in the same way	I might have over done the pins a little!
If you lay your bag out flat it should look like this.	Exterior bag view Inside view.
Sew in the sides Make a fabric sandwich with the side pieces in just the same way as you did for the bag bottom. Fuse your pieces together if you’re using fusible fleece or pin everthing securely together down the middle of the side piece if you’re not. Place the short edge of the side piece together with the short edge of the bottom piece. Linings should be facing one another. (The photograph should help to clarify this!) Sew the bottom (short edge) to the bottom piece of your bag, leaving the 1.5cm seam allowance open at each end so that you can sew the sides up without too much stress. I’ve marked this with a pen (Removable - don’t panic.). Repeat this for both sides.	Looks a bit unlikely at the moment doesn’t it?
Attach the side pieces Take the attached side piece (now sewn to the bag ‘bottom’ piece) and pin it to the side of the bag front piece. (long side to long side.) Check that all the fabric is tucked securely into the seams and nothing has got rucked up or wrinkled. It should be fairly straightforward to fix everthing together. Remember that the seams are on the outisde and sew. Repeat for the other sides.	Nearly a bag - I quite like the look with the top turned over.
Completing the top edge Now we need to sew around the top of the bag. It looks like quite a tight fit but just remove the extension ‘table’ piece to your sewing machine and it should fit around it quite nicely. Sew approximately 5cm (2 inches) down from the top edge if you want to turn over the top as I have. If you don’t want to, then sew all the way around at least 1.5 cm (1/2 an inch) from the top edge. If you’ve made a separate lining then insert this into your bag and top stitch it into place in the same way.
More snipping! O.K. now is the point at which to do a little more snipping. Start by completing any snipping/cutting out of your design. Next snip vertically into the seam allowances being careful not to snip your stitches at approximately 0.5cm to 1cm (approximately 1/4 to 1/2 an inch) intervals all the way around your shape. Do this for every shape, front and back and for all the outward facing seams including the top edge. Don’t forget though that sometimes less is more and it’s easier to snip more fabric away later than try and add some back in!	Can you see all those little thready bits bidding for freedom!

Making the handle

Join all the pieces of 5cm (2 inches) wide denim together using a 1.3cm (1/2 inch seam) until you have a strip approximately 35 inches long.	Seams are on the right side facing out.
Place the fabric strip for the handle rightside facing down onto your work table. Place the 2.5 cm (1 inch) wide wadding/batting/fusible fleece centrally onto this. Place the denim strip you’ve created rightside facing up onto this. Make sure that sides are all neatly aligned and pin or fuse everthing into position. Machine stitch 1.5cm (1/2 inch) down one long side of your strap, and then down the otherside, again 1.5cm (1/2 inch) from the edge. It is possible because of the width the handle to sew four equally spaced ’stitched lines’. This makes a really strong and sturdy handle.Sew across the handle ends 1.5cm (1/2inch) from the edge.	Snip into the seam allowance all around the handle and at the handle ends. Same as before at 0.5 to 1cm intervals (approximately 1/4 to 1/2 and inch) and being careful not to cut into your stitches. Do this to any outward facing seams where you’ve sewn strips together to make the handle length.
Fix handles to the bag Position the handle 10 cm down on the bag ’side’ panel. (If you’re not going to turn the bag top over you may wish to attach your handle higher up the bag.) Sew both ends of your handle to your bag ‘body’. I sewed a rectangle and then sewed across the diagonal both ways. Ensure that you leave a 1.5cm (1/2 inch) at the sides and the bottom of the handle to ensure that these will fray. (For once fraying = good)	I’ve marked where I’m going to sew.
For a bit more decoration I sewed buttons over where the handle is fixed to the bag.	The bag complete with handles! You can see all the snipping.
To complete your bag Put your bag in the washing machine and wash it. Note: because denim frays you may prefer to wash it in a wash bag or pillowcase to avoid getting all those bits on other items. A cool wash will do. All the ‘agitation’ (Hopefully not yours!) causes the denim to take on that really frayed look and the lining and ‘backing fabric’ colours should show beautifully in the seams too. Wash completed. Dry your bag! If you happen to be using the tumble dryer - that helps with the fraying too. Inspect your bag. Does your design show up as well as you hoped? I found that I hadn’t cut enough fabric away from the outer square in the middle of my design so the ‘backing fabric’ didn’t show up as well as I wanted it to. So, I snipped out a little more and washed and dried it again. Love it now!	One view without the top edge folded down.(It’s stuffed full of tissue to help it stand up!) Another view with the top edge folded down.

Congratulations if you got this far and if there’s anything I’ve missed or just not explained very well, just contact me and I’ll try and ‘explain’ myself.

If you try out this ‘frayed technique’ to make a bag I’d really love to see it.

…….. but not necessarily in that order!

I’ve had a lot of fun today putting ‘fabriccy bundles’ in the shop.

Za Za by Erin Michael

Amy Butler fabrics - damask rose palette

I’ve added some three, four, and five piece ‘bundles’ or should I say ‘collections’? See I can’t even decide what to call them.

What do you think? Do you think they’re o.k?

Sadly, I can’t claim all the credit for the content of these ‘bundles’ as these fabrics have been designed in palettes so ….. what can I say? I enjoy that ‘bit’ you know when you place fabrics side by side and the colours, patterns all interact to completely change the look and feel of something - pure magic.

You can see this quite clearly on Amy Butler’s own website. She has an ‘Inspiration’ section and you can see how she achieves lots of different looks from one pattern or idea with the different colour/pattern combinations. Nothing less than brilliant! Not to mention helpful.

If you do visit Amy’s site then you just have to take look at the ‘free’ (yes - really free!) projects that Amy posts. There are quilts, cushions, eye pillows, yoga bags, card holders, portfolio’s - just loads. (You did look didn’t you?) They’re in PDF format and everybit as well written as her published patterns. Go on, be inspired or should it be ‘risk being tempted’ (say the last phrase in a very deep voice for the full effect, preferably with an echo).

Amy has also just issued an update to her ‘Birdie Sling pattern’, which if you’ve purchased this pattern you’ll find here in the pattern updates, hints & corrections section of her website. The e-mail says that this is an improvement on the previous instructions as opposed to correcting an error or ommission.

So, I know this is two posts in one day but I’d really love to know if you think that there are any other bundles I could/should add to the shop? Comments are very welcome, I hate to think i’m sitting here alone.

One more thing has anyone tried ‘crazy patchwork’, and are there any particular books you’d recommend. I feel like trying something different you see.

Sorry! I couldn’t resist the title.

My two little buttons have morphed and this is what they became.

The blue one became the middle of a yo-yo which I trimmed with a little ric-rac. I think it looks quite olde worlde, vintage like . Nice simple touch to add to a t-shirt.

The little burgundy red button became the centre of an embelishment for a ’sometime soon project’ (is this an SSP as opposed to WIP? ) of a summer hat - for me. I just can’t decide whether to make this one or this one. (Decision making is definitely not my strong point.) Is it greedy to make/have both?

I like the effect of nesting two yo-yo’s together, it makes them look a bit flower like. (The fabrics are these)

Thinking about it, yo-yo brooches would probably be a great thnig to make to sell at a craft fair. They’ve got that kind of ‘folksy’ charm about them, making a fantastic addition to a ‘crafty’ outfit and they’d not be too expensive to make. Use up lots of odd and ends of fabric too.

If you want a tutorial for making yo-yo’s then you probably can’t do better than this. . (I think Marmadaisy said that in her hat ‘recipe’ too and whenever two blogers agree well, you have to check it out don’t you?.)

Forgive me, bit I’m just a little fixated on buttons at the moment, don’t be concerned - I’m sure I won’t come to any harm but I do absolutely have to share.

It is completly possible to create beautiful unique buttons by isolating just a part of a pattern motif of the fabric - but you knew that didn’t you?

When I’m covering larger buttons I often use a piece of wadding cut to the same size as the button top under the fabric. I think it softens the look of the button slightly and it just feels nice. If you’re usng a metal button kit it also stops the metal shining through particularly if your fabric has a more open weave. Really though it’s purely a matter of personal choice.

Requirements

• self-cover buttons - front and back (there are many different sorts of self cover button kits, but I use this sort. Link)
• fabric (enough to cover your button)
• small piece of wadding (optional)
• matching sewing thread
• sewing needle
• scissors
• tape measure
• a few pins
• greaseproof paper, tracing paper or tissue paper (something you can see the fabric pattern through)
• a pencil to make a pattern with or fabric marker (if you’re going to mark directly onto the fabric)
• glue stick (optional) (Tip: raid the children’s pencil cases. They’re bound to have one)

Step 1 - Make your button pattern a) Place the button front face down onto the tissue paper (or whatever you’re using) and draw around the outside of the button top. Not the smoothest circle but it’ll work just fine.
b) Measure the distance between the button shank and the outside rim of the button, like so. In this case it’s just a little more than a 1cm - a centimetre will work just fine.
c) Use this amount to mark a seam allowance (1cm) around the circle you have just drawn.
(To draw this outer circle I place the tape measure against the circle I drew by marking around the button top and mark the 1cm distance with dots. Then I can just join up the dots to make my outer circle.) You should now have something like this which you can cut out and use as a pattern piece. Alternatively, you can draw directly onto your fabric with a non-permanent or other fabric marker.
Step 2 - Selecting the part of the fabric pattern you wish to use a) Decide which part of the fabric pattern you wish to use.
Your ’see-through’ pattern piece should help you isolate the area you’re interested in and judge what it would look like on the finished button. Move it round until you’re happy with your decision. b) Pin your pattern piece to the fabric and cut it out. If you’ve marked the ‘button pattern’ directly onto the fabric then cut that out. The ’see-through’ tracing paper allows me to see the pattern quite clearly so I can accurately select the pattern motif I want to cut from the fabric for my button.	I love this fabric it’s from Anna Maria Horner’s chocolate range
Step 3 - The wadding For this button I wanted to include a piece of wadding just because …..I like my buttons that way!? a) If you don’t intend to keep the pattern piece you just used to cut out the fabric circle with forever …. and you might do. Then cut off the seam allowance marked on you pattern piece and use this as a pattern to cut out a circle of wadding for the top of your button.
Step 4 - Lots of bits and pieces a) Get out the glue stick This just helps to hold the wadding in place whilst you concentrate on the fabric, so it’s an entirely optional step. (I do it ‘cos I get impatient with trying to hold lots of things still.)
b) Rub a little glue onto the button top and press the wadding onto it
c) Using a doubled sewing thread which matches the fabric colour, sew a row of running stitches around the edge of the fabric circle. Be careful not to sew too close to the edge or when you gather up the fabric the stitches may pull out. (I’m admitting nothing!)
d) Slip the button front onto the fabric circle, and gently pull up the stitches.
Whilst you’re doing this ensure that the pattern motif that you so carefully selected is positioned exactly as you want it.
e) Pull the gathers up tightly so that the button top if completely enclosed and tie the thread ends off securely in a knot. Snug as a bug in a rug!
Step 5 - Assembling your button pieces a) Place the ‘washer’ over the button shank with the ’spotty’ side facing what will be the underside of the button. The serrated edge and these spots help to hold everything nice and tightly in place.
b) Use a little brute force and push the washer down onto the other button piece. The washer should click into place.
Stand back, admire your lovely new button and Smile!

I hope you like this little tutorial and that I haven’t make it look too complicated. Let me know what you think, I’d hate to think that I was talking to myself as well as everthing else. I’d love to see any buttons you cover, ‘cos I’m nosy interested. Happy sewing.

Fabric covered buttons

I love buttons.

Any buttons! They’re useful and pretty ….. what more could you ask for?

You can buy/beg or otherwise get hold of some beautiful buttons these days. Sometimes though the best button is the button you created yourself!

Cover them with your favourite fabric, either solid colour or patterned, embroidered, embellished with beads, sequins or both, fabric painted. So much choice, so much possibility!

I mean look at these or this collection I mean wow! Creative or what?! You’d just have to cuddle them wouldn’t you? …Did you come back?

Even if you’re not up to doing this just yet (and I’m not sure I am) there’s so much fun you can have with them and so much you can do with them. I make them to add detail to bags, scarves, hats and belts. I have been know to change buttons on jackets for buttons I’ve covered myself. (Makes ‘em look good. Here you have to imagine a plain black jacket with red fabric buttons. Well, I liked it.)

Anyway, I was thinking as I was adding ‘plastic self-cover buttons’ to the shop that it’d be nice to have a little ‘How to..’ about the place for peeps who haven’t covered a button before.

So, without any more ado, here begins a little ‘tutorial’ ( a bit grand, but I wasn’t sure anyone else uses the term ‘a how to…’) on ‘covering a button with fabric’.

First of all you need;

Requirements;

• 1 set of plastic self-cover buttons (there are many different sorts of self cover button kits, but I use this sort.)
• fabric
• matching sewing thread
• sewing needle
• a few pins
• scissors
• paper and pencil to make a pattern or
  fabric marker
• tape measure

For this I’m using an 18mm plastic button, which is quite small. All sizes of buttons can be covered using the same method but you will need to allow a larger seam allowance for larger buttons in order to get everthing nice and smooth and safely secured behind the button back.

I like to make a pattern first.

Step 1 Make yourself a template/pattern a) Place the button front face down onto a piece of paper and draw around the outside.
b) Measure the distance between the button shank and the outside rim, like so. It’s approximately 7mm.	Notice in the photo the amount of space (or lack of it) on the back of the button, between the shank and the edge. There isn’t great deal of room to secure/hide lots of fabric. Too much fabric and you’ll get rucks or gathers on the edge/front of the button which just isn’t nice. Too little fabric and it’ll fray out over time. (In other words a pattern helps.)
c) Use this amount to mark a seam allowance (7mm) around the circle you have just drawn. Like so. Cut out your pattern piece. Alternatively draw directly onto your pattern with a non-permanent or other fabric marker.
d) If you are using a pattern; Pin it to your chosen fabric and cut it out. If you’ve marked the pattern directly onto the fabric then cut that out.
Step 2 Gathering up the fabric to cover your button a) Using a doubled sewing thread which matches the fabric colour (mine doesn’t because I wanted it to show in the photo), sew a row of running stitches around the edge of the fabric circle.	Be careful not to sew too close to the edge or when you gather up the fabric the stitches may pull out.
b) Slip the button front onto the fabric circle, and gently pull up the stitches.
Step 3 Completing your button Almost done. a) Pull the gathers up tightly but carefully and tie the thread ends off in a knot. b) Look at your button and smooth out any rucks in the fabric. It is usually possible to ease the fabric about a little. Be patient but show the button who’s in charge.	Happy that it’s all smooth and even? Good.
c) Place the ‘washer’ over the button shank with the ’spotty’ side facing what will be the underside of the button. The serrated edge and these spots help to hold everything nice and tightly in place.
d) Use a little brute force and push the washer down onto the other button piece. They can be quite stiff but you should hear the washer click into place.

Ta da! One fabric covered button perfectly lovely and ready for your next or even your current project. Is this your first butonny adventure? I wonder what next?

Just in case you haven’t been paying attention … I really do like making pouches. They’re quick (well, sometimes), you can still play with mixing up fabrics, use up little bits of fabric, you can patchwork, you can quilt or just let the fabric speak for itself. You can get a quick ‘crafty/quilty’ kind of fix and have something good at the end of it.

I find them really useful for organising little bits and pieces that otherwise might get lost. I use them for sewing bits and pieces if I go somewhere else to craft/sew or knit. I use them for make-up, my daughter uses them for all her hair bits ties and bands and clips and, and ….. You’ think therefore wouldn’t you that projects would go smoothly, no issues, no pain but sometimes it doesn’t all go according to plan.

This one was o.k. I was pleased with the way the fabrics went together and the lining is in a lovely little ‘paprika’ coloured (well, it is a kind of orangey red’) polka-dot. I think you can just see it in the photo. The binding at the top was a new thing for me and I like the effect a lot. I think it makes the whole thing looks finished. I also inserted the zip differently too. I sewed fabric on to the zip ends so that when you’ve finished the zip sits nice and flat on the top. So, two good things about this pouch as far as I’m concerned.

Next up, is this little patchwork number. Made out small squares of Amy Butler prints, mostly from the nigella range. (Can you name them all?) I couldn’t get the zip in as well as I like to. Was it me? Hadn’t I drunk enough coffee that day? Who knows - but I think I’d have completely ruined it if I’d continued to unpick the zip. I suppose if I’d have added a binding to the top edge I might have found it easier to keep the fabric flat ? Anyway, it’s another little pouch for me.

This next one is a complete monster of a pouch - you could probably get some hefty hair brushes in this one! No, I didn’t intend it to be this big but well the pattern I was following (Yes, this time I thought I’d try something different. ) said …. and I just followed and …. well. Don’t get me wrong I love the way the fabric goes together and I’m not unhappy with the free motion quilting. The lining is beautiful but it’s just too big.

(Reminds me of those pictures of Viking longships you see!)

I’ve always used boxed corners in these little pouches and this pattern uses some (complicated) folds. Which look great I just couldn’t get everything square without a bottom seam to measure everything against.

My son reckons that I had a ‘blonde’ moment - cheek, he’s a lot blonder than me. I’m going to have another go. No, doubt you’ll be hearing about it.

The last week has been a strange one. An earthquake …which rumbled away in the small hours, then gales followed by a sprinkling of snow and now beautiful sunshine.

Read more